The routing protocol specified may require additional options. This step is necessary for the switch to exchange dynamic routing updates with other routing devices. Switch(config)#router ip routing_protocol (Optional) Specify an IP routing protocol. Switch(config-if)#ip address n.n.n.n subnet-maskĪssign an IP address to the SVI for the VLAN. Steps for Inter-VLAN Routing ConfigurationĬreate the SVI interface or navigate to configuration mode for the interface. To configure a routed port, perform these steps. Switch(config)#router ip_routing_protocol Step 4 : Configure the IP routing protocol if needed. Switch(config-if)#ip address ip-address mask Labrouter#ping 8.8.8.Step 3 : Assign an IP address to the routed port. Sep 30 21:49:21.246: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet4, changed state to up Sep 30 21:49:20.246: %LINK-3-UPDOWN: Interface FastEthernet4, changed state to up Sep 30 21:48:47.718: %SYS-5-CONFIG_I: Configured from console by console Labrouter(config)#ip access-list extended NAT You can check your IP address and find the IP address of the router by using the ipconfig command. Labrouter(config)#ip access list extended NAT Labrouter(config)#ip nat inside source list NAT int fastEthernet 4 overload Labrouter(config)#ip nat inside source list NAT int fastEthernet 4 over Labrouter(config)#ip nat inside source list NAT int fa is it setup wrong? Do I have to try any setup the static again instead? See response from router below. For some reason the router will not pull an ip address over DHCP. I did what you said but it still wont work. That's what I thought just needed to be sure as I don't have CLI commands memorized. router> enable router configure terminal router (config) interface Fast0/0 router (config-if) ip address 192.168.1.1 255.255.255.0. The system interface assigns an IP address to the. For a Cisco router, you configure an IP address on a specific interface: Text.
NVI0 unassigned YES unset administratively down down The following command sequences create a system and a logical IP interface. Cisco Router Basic Operations - Covers getting into and out of different modes. Cisco Router Show Commands - Handy show commands to check on the status of interfaces.
Interface IP-Address OK? Method Status ProtocolįastEthernet0 unassigned YES unset down downįastEthernet1 unassigned YES unset down downįastEthernet2 unassigned YES unset down downįastEthernet3 unassigned YES unset down down Cisco Router Configuration Commands - Lists how to enable and disable interfaces, add IP addresses to interfaces, enable RIP or IGRP and set passwords. The customer has been assigned Public IP address by ISP as below. The Gateway Router is further connected to Internet Service provider (ISP). % Invalid source interface - IP not enabled or interface is down In the setup, R1 and R2 routers in LAN have been configured as end systems (host machines) which are connected through a Layer 2 Switch (SW) to customer Gateway Router (R3). Labrouter#ping 8.8.8.8 source fastEthernet 4 Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds: In order to assign an IP address to a VLAN, simply go to VLAN and set the IP address like assigning IP address to an interface of a router. Sep 30 21:01:22.886: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet4, changed state to up But when you are trying to configure an ip address of the same previous subnet (connected route) but on a different interface the router gets confused since for the same. You will see that by executing 'show ip route'. Configure IP addresses for the systems in the network and set the gateway IP as the. When you configure an IP address on an interface, the router will add the network of that IP address as a connected route. Sep 30 21:01:21.886: %LINK-3-UPDOWN: Interface FastEthernet4, changed state to up Thats all you need to enable inter Vlan routing on a cisco router.
! NVRAM config last updated at 17:00:21 SUMMER Wed Sep 30 2015Ĭrypto isakmp key XXXXXXXX address ! Last configuration change at 17:00:19 SUMMER Wed Sep 30 2015
License udi pid CISCO881-SEC-K9 sn FTX155382K0Ĭrypto isakmp key XXXXXXX address Ĭrypto ipsec transform-set Chris-Home esp-3des esp-sha-hmacĬrypto map cisco_1_to_sonicwall_1 10 ipsec-isakmp ! NVRAM config last updated at 11:35:50 SUMMER Wed Sep 30 2015Įnable secret 5 $1$VVP3$S54zJ7vK9sYUDlDnruCZm. ! Last configuration change at 11:42:10 SUMMER Wed Sep 30 2015